Investigation of the Nodularisation Propensity of Calcined Cashew-Nut Shell-Ash in Cast-Iron Melt Graphite
Keywords:
Nodularisation, Ductile-iron, Cashew-nut, Ferrosilicon-magnesium alloy, Mechanical propertiesAbstract
Production of ductile iron using ferrosilicon-magnesium master alloy in melt treatment is currently fraught with challenges bothering on cost and availability. In this study the suitability of cashew nut shells ash (CNSA) as a viable alternative to magnesium master alloys employed in the treatment of molten cast iron for enhanced mechanical properties was studied. The carbonized CNSA used varied from 2-10 wt. % to treat different heat batches; CA1-CA5 containing varied amount of CNSA, CaO and FeSi in the molten cast iron. The cast samples were subjected to both mechanical characterisation (tensile, hardness and impact) and microstructural analysis using Instron electromechanical machine, impact tester and scanning electron microscope (SEM) coupled with energy dispersive spectroscope (EDS). Results show that the 8 wt. % CNSA addition demonstrated the best mechanical properties comparable to ASTM A536 ferritic ductile cast iron. Specifically, the 8 wt. % CNSA cast samples exhibited 433 MPa tensile strength, 144HRC hardness and ductility of 14.7%. Contributions to improved mechanical properties may be attributed to the development of sufficient fractions of graphite nodules during melt treatment with CNSA. These outcomes are a boost both to the production of quality ductile irons and a cleaner environment.
References
Adeigbe, O.; F. Olasupo; B. Adewale; and A. Muyiwa. (2015). A Review on Cashew Research and Production in Nigeria in the last Four Decades. Academic Journals, 10 (5): 196-209.
Al-Ghonamy, A.; M. Ramadan; N. Fathy; K. Hafaz; and A. El-Wakil. (2012). Effect of Graphite Nodularity on Mechanical Properties of Ductile Iron for Waterworks Fittings and Accessories. International Journal of Civil & Environmental Engineering, 10 (3): 1-5.
Bahubali, B. and Vasudev, D. (2013). The Effect of Inoculation on Microstructure and Mechanical Properties of Ductile Iron. Journal of Mechanical and Civil Engineering, 5 (6): 17-23.
Borse, C. and Mangulkar, Y. (2014). Review of Grey Cast Iron Inoculation. International Journal of Innovative in Science, Engineering and Technology, 3 (4): 31-35.
Bui, A., T. Le; and B. Nguyen. (2012). Decarburisation of Molten Iron under Reduced Pressure. ASEAN Engineering Journal B, 3 (1): 55-61.
Bravo S.; K. Yamamoto; H. Miyahara; and K. Ogi. (2007). Control of Carbides and Graphite in Ni-Hard Type Cast Iron Hot Strip Mills. Materials Science Forum, 361: 1023-1026.
Cocco, V. and Iacoviello, F. (2015). Pearlitic Ductile Cast-Irons: Fatigue Initiation Micromechanics. Procedia Engineering, 109: 465-472.
Cofino-Villaz, A.; F. Alrarez-Antilus; J. Asesio.; and M. Garcia. (2019). Control over the Percentage, Shape and Size of the Graphite Particles in Martensitic White Castings Alloyed with Cr, Nb and Mg. Materials, 12: 185-193; https://doi.org/10.3390/ma1210185.
Conejo, A. and Hermandez, D. (2006). Optimisation of Aluminium De-oxidation Practice in the Ladle Furnace. Materials and Manufacturing Processes, 21 (8): 796-803.
Ecob, C. and Hartung, C. (2003). An Alternative Route for the Production of Compacted Graphite Iron. Elkem Foundry Production, 23: 7-23.
Hanus, A. and Hanusova, A. (2012). Continuous Modification of Cast Iron by FLOTRET Method. Archives of Foundry Engineering (VERSITA) 12 (1): 43-48.
Hartung, C.; D. White; K. Copi; M. Liptak; and R. Logan. (2014). The Continuing Evolution of MgFeSi Treatments for Ductile and CG Irons. International Journal of Metal Casting, 8 (2): 7-15.
Hatate, M.; T. Shiota; N. Takahashi; and K. Shimizu. (2001). Influence of Graphite Shape on Wear Characteristics of Austempered Cast Irons. Wear, 251: 885-889.
Huerta, E. and Popovski, V. (2005). A study of Hold-Time, Fade Effects and Microstructure in Ductile Iron. Proceedings of the American Foundry Society (AFS) cast iron inoculation conference, Schaumburg, Illinois, 44-54.
Iacoviello, F.; V. Cocco.; and M. Cavallini. (2016). Fatigue Crack Propagation and Overload Damaging Micromechanisms in a Ferritic-Pearlitic Ductile Cast Iron. Fatigue & Fracture of Engineering Materials & Structure, 39 (8): 999-1011.
Jekayinfa, S. O.; and O. S. Omisakin. (2005).Energy Potentials of Some Agricultural Wastes as Fuel Materials in Nigeria. Agricultural Engineering Ejournal, 7: 51-63.
Marcin, S.; J. Krzystof.; and D. Malwina. (2017). Selected Phenomena of In-mould Nodularisation Process of Cast Iron that Influences the Quality of Cast Machine Parts. Journal of Processes, 68 (5): 2-9.
Nakae, H.; and H. Shin. (2001). Effect of Graphite Morphology on Tensile Properties of Flake Graphite Cast Iron. Materials Transactions, 42 (7): 1428-1434.
Nicoletto, G.; L. Collini.; R. Konecna.; and E. Riva. (2006). Analysis of Nodular Cast Iron Microstructure for Micromechanical Model Development. International Journal for Environmental Mechanics, hpps://doi.org/10.1111/j.1475.
Obi, F. O.; B. O. Ugwuishiwu.; and J. N. Nwakaire. (2018). Agricultural Waste Concept, Generation, Utilisation and Management. Nigerian Journal of Technology, 35 (4): 957-964.
Ogundiran, M.; J. Babayemi.; and C. Nzeribe. (2011). Application of Waste Cashew Nut Shell for the Control of Pb and Cd Mobility in Waste Battery Contaminated Soil. Pacific Journal of Science and Technology, 12 (2): 472-475.
Olawale, J. O.; K. M. Oluwasegun; D. Ezemenaka.; and S. Adisa. (2014). Production of Austempered Gray Iron (ADI) Using Forced Air Cooling. Materials Performance and Characterisation, 3 (1): 355-370.
Olawale, J. O.; S. A. Ibitoye.; and K. M. Oluwasegun. (2016). Processing Techniques and Production of Ductile Iron: A Review. International Journal of Scientific and Engineering Research, 9 (7): 397-416.
Souza, T.; R. Nogueira.; J. Franco.; M. Agullar.; and P. Cellin. (2014). Mechanical and Microstructural Characterisation of Nodular Cast Iron with Nobium Addition. Materials Research, 17 (5): 1167-1172.
Tvarozek, J.; and M. Lickova. (2013). Structural and Stress Conditions of Graphite Cast Irons after Intense Heating and Controlled Cooling. American International Journal of Contemporary Research, 3 (3): 49-67.
Vaskova, I.; P. Sebek.; and I. Mulik. (2013). Hardness of Ductile Cast Iron Castings and Control. Manufacturing Technology, 13 (1): 120-122.
Walter, D. and Pilkey, F. (2007). Peterson’s Stress Concentration Factors. 3rd, John Wiley & Sons, Inc., Hoboken, New Jersey, 214.
Wang, Z.; X. Zhang.; F. Xu; K. Oian; and K. Chen. (2019). Effect of Nodularity on Mechanical Properties and Fracture Ferritic Spheroidal Graphite Iron. China Foundry, 16: 386-392.
Additional Files
Published
Issue
Section
License
Copyright (c) 2021 Nigerian Journal of Technological Development
This work is licensed under a Creative Commons Attribution-NonCommercial-ShareAlike 4.0 International License.
In accordance with the Copyright Act of 1976, which became effective January 1, 1978, the following statement signed by each author must accompany the manuscript submitted: "I, the undersigned author, transfer all copyright ownership of the manuscript referenced above to the Nigerian Journal of Technological Development, in the event the work is published. I warrant that the article is original, does not infringe upon any copyright or other proprietary right of any third party, is not under consideration by another journal, and has not been published previously. I have reviewed and approve the submitted version of the manuscript and agree to its publication in the Nigerian Journal of Technological Development." A copyright transfer form should be downloaded from the NJTD Website ( http://njtd.com.ng/index.php/njtd). Author(s) will be consulted, whenever possible, regarding republication of material. All authors must have access to the data presented and the authors and sponsor (if applicable) must agree to share original data with the editor if requested.
